View PT2256V_1016519.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Tel:886-2-66296288 Fax:886-2-29174598 URL:http://www.princeton.com.tw
Electronic Volume Controller IC
PT2256V
DESCRIPTION
PT2256V is an electronic volume controller IC utilizing CMOS Technology specially designed for use on audio equipment. It has 2 built-in channels making it ideally suitable for mono and stereo sound applications. PT2256V provides the Loudness Function, a wide frequency response range and a very low total harmonic distortion, thereby guaranteeing a highly effective and reliable performance. It is housed in 16-pin DIP or SOP and is functionally compatible with TC9235P. Pin assignments and application circuit are optimized for low cost advantages and easy PCB Layout.
FEATURES
* * * * * * * * * * * CMOS Technology Low Power Consumption Wide Operation Voltage Range: VDD=4.5 ~ 11V Least External Components 2 Channels in the same chip 0dB to -78dB Attenuation can be controlled by UP and Down Pin 20dB Tap for Loudness Circuit Built-in DC Output Circuit (8 levels) for Volume Level Metering Wide Frequency Response Range Low Total Harmonic Distortion Available in 16 pins DIP or SOP
APPLICATION
* Audio Equipment Volume Control
PT2256V V1.2
-1-
August, 2006
Tel:886-2-66296288 Fax:886-2-29174598 URL:http://www.princeton.com.tw
Electronic Volume Controller IC
PT2256V
BLOCK DIAGRAM
VS S OUT1 IN 1 LT 1 AG N D VD D OUT2 IN 2 LT 2 AG N D
D e co d e r /U P /D N O SC U p /D o w n C o u n te r C o n tr o l
D/A Con ve rte r
DCO /I N H /R ST
PT2256V V1.2
-2-
August, 2006
Tel:886-2-66296288 Fax:886-2-29174598 URL:http://www.princeton.com.tw
Electronic Volume Controller IC
PT2256V
PIN CONFIGURATION
VSS OUT1 IN1 LT1 AGND /UP /DN OSC 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 VDD OUT2 IN2 LT2 AGND DCO /INH /RST
PT2256V
PIN DESCRIPTION
Pin Number VSS OUT1 IN1 LT1 AGND UP I/O O I O I Description Negative Power Supply Volume Output Pin 1 Volume Input Pin 1 Tap Output Pin 1 for Loudness Function Analog Ground Pins 1 Volume UP Control Input Pin. The 1 step/1 push volume is controlled by pressing the UP Key. If the key has been pushed continuously increase. Built-in Pull-up Resistor. Volume DOWN Control Input Pin. The 1 step/1 push volume is controlled by pressing the DOWN Key. If the key is continuously pressed, the volume control will continuously decrease. Built-in Pull-up Resistor. Oscillation Pin. The oscillation circuit of a resistor and capacitor connection. Oscillator is activated when the key is pressed. Reset Pin. This pin sets the initial volume level. The volume level is set to -46dB by "L" Input. Built-in Pull-up Resistor Low Active Backup Mode Input Pin DC Output Pin for Volume Level Meter Tap Output Pin 2 for Loudness Function Volume Input Pin 2 Volume Output Pin 2 Positive Power Supply
-3-
Pin No. 1 2 3 4 5, 12 6
DN
I
7
OSC RST /INH DCO LT2 IN2 OUT2 VDD
PT2256V V1.2
I/O I I O O I O -
8 9 10 11 13 14 15 16
August, 2006
Tel:886-2-66296288 Fax:886-2-29174598 URL:http://www.princeton.com.tw
Electronic Volume Controller IC
PT2256V
FUNCTION DESCRIPTION
ATTENUATION
The PT2256V volume control circuit consists of ladder resistors and analog switches. The Tap for loudness function is connected to the Step 10 (-20dB). When the (3.9K) resistor is connected between LT and AGND pins, the attenuation is given in table below. The equivalent circuit is shown below: Step 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Attenuation (dB) 0 -2 -4 -6 -8 -10 -12 -14 -16 -18 -20 -22 -24 -26 -28 -30 Step 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Attenuation (dB) -32 -34 -36 -38 -40 -42 -46 -50 -54 -58 -62 -66 -70 -74 -78
OUT IN Step 0 Step 1 Step 2 29K
Step 9 LT Step 10 Step 11
22K
Step 30 AGND Step 31
Note: 1. Step 22 has an initial value of -46dB.
PT2256V V1.2
-4-
August, 2006
Tel:886-2-66296288 Fax:886-2-29174598 URL:http://www.princeton.com.tw
Electronic Volume Controller IC
PT2256V
DC OUTPUT FOR VOLUME LEVEL
The DC Output for the Volume Level Meter is internally connected to the D/A Converter. PT2256V has 8 stages of output voltage with each stage corresponding to a particular volume level. Please refer to the table below: Step 0-3 4-7 8-11 12-15 16-19 20-23 24-27 28-31 Attenuation (dB) 0-6 8-14 16-22 24-30 32-38 40-50 54-66 70- Output Voltage (V) 7/8 VDD 6/8 VDD 5/8 VDD 4/8 VDD 3/8 VDD 2/8 VDD 1/8 VDD 0
UP/DOWN VOLUME CONTROL
PT2256V features two Volume Control Pins, namely: UP and DN. UP is the control pin used to increase volume level while the DN is the control pin used to decrease the volume level. Thus, volume level may regulated using the Up or Down Keys. These keys are operated on a 1 step/1 push volume level control when UP or DN keys are set to "L" Level. If the keys are continuously pressed (input "Low"), then the volume level continuously steps up or down as the case maybe. Please refer to the diagram below for the timing of the key input.
/UP, /DN Input Volume Level Control
t
T
a
Notes: 1. t= Preventive Time for Chattering (2.2 x 1/fosc ) 2. T= Switching Time to Automatic Mode (10 x 1/fosc) 3. a=Up, Down Speed (2x1/fosc)
PT2256V V1.2
-5-
August, 2006
Tel:886-2-66296288 Fax:886-2-29174598 URL:http://www.princeton.com.tw
Electronic Volume Controller IC
PT2256V
INITIALIZATION WHEN POWER ON
PT2256V has an auto-initialization function during the Power On period. When Power is turned ON, the volume level is set to the initial value of -46 dB by setting the RST pin to "L" level. Please refer to the diagram below.
VDD VDD VIL 0V T /RST T 1ms
BACK UP WHEN POWER OFF
When the /INH Pin is set at "L" Level, all input and output pins are disabled and the current consumption is reduced to the minimum. Under this condition, the backup becomes possible. Please refer to the diagram below:
VDD VDD
B ac ku p
4 . 5V 0V
No rm al M ode B ac ku p M od e
V D D m in > 4 .5 V
B ac ku p D ata is los t No rm al M ode
The backup circuit is given below:
10 K V DD IN4 001 51 K
VD D /I NH
10 K + -
P T 225 6V
VSS
1 000 F /16 V
Notes: 1. If the VDD drops from 11V to 4.5V, then the backup is possible for a period of 6 days. However, if VDD-Vss drops below 4.5V, the backup becomes impossible.
V SS
PT2256V V1.2
-6-
August, 2006
Tel:886-2-66296288 Fax:886-2-29174598 URL:http://www.princeton.com.tw
Electronic Volume Controller IC
PT2256V
LOUDNESS FREQUENCY RESPONSE
The figure below shows the Loudness Frequency Response Diagram.
0dB -6dB -12dB
-42dB
-54dB -66dB -78dB
PT2256V V1.2
-7-
August, 2006
Tel:886-2-66296288 Fax:886-2-29174598 URL:http://www.princeton.com.tw
Electronic Volume Controller IC
PT2256V
ABSOLUTE MAXIMUM RATINGS
(Unless otherwise specified, Ta=25) Parameter Symbol Supply Voltage VDD Input Voltage VIN Power Dissipation PD Operating Temperature Topr Storage Temperature Tstg Rating -0.3 to 12 -0.3 to VDD+0.3 300 -40 to +85 -65 ~ +150 Unit V V mW
PT2256V V1.2
-8-
August, 2006
Tel:886-2-66296288 Fax:886-2-29174598 URL:http://www.princeton.com.tw
Electronic Volume Controller IC
PT2256V
ELECTRICAL CHARACTERISTICS
(Unless otherwise specified, Ta=25, VDD=9V) Parameter Symbol Test Condition Min. Typ. Operating Supply Voltage VDD 4.5 9.0 Operating Supply Current IDD No Load, FOSC=20Hz 0.3 Stand-by Current ISB OSC=0V, /INH=0V 0.3 Backup Voltage VOD 2.0 /INH Pin=0V Backup Current IOD 0.1 /UP, /DN, /RST 0.7VDD High Level Input Voltage VIH /INH 0.8VDD /UP, /DN, /RST 0 Low Level Input Voltage VIL /INH 0 Between IN~AGND Resistor 45 54 Voltage Resistor RVR Between IN~LT Resistor 26 29 Between LT~AGND Resistor 19 22 High Level Input Current IIH /INH Input Pin, VIL=VDD -1 Low Level Input Current IIL /INH Input Pin, VIN=0V -1 Pull-up Resistor Rup /UP, /DN, /RST Input Pin 50 70 When 0dB, Between Analog Switch ON RON IN1~OUT1 and IN2~OUT2 400 Resistor Resistor ATT Test Attenuation Value Attenuation Error 0 Balance between Left and Volume Resistor Error RVR 0 Right between Left and Right Total Harmonic Distortion THD 0dB 0.01 FIN=1KHz, Maximum Attenuation ATTMAX VIN=1Vrms, dB 90 RL=100K, Cross Noise CT 0dB 90 Rg=600 Output Noise VN 0dB -100 OSC Frequency FOSC CX=2.2f, Rx=33K 18 FIN=1KHz, VIN=1Vrms, Output Resistance ROUT 550 650 Volume Control=0dB FIN=1KHz, Volume Maximum Input Amplitude VIN VDD=9V Control=0dB, THD<0.08% Max. Unit 11 V 1.0 mA 10 A 11 V 1.0 A VDD V VDD 0.3VDD V 0.7VDD 75 K 45 32 1 mA 1 mA 100 K 500 2.0 3.0 750 3.5 dB % % dB dB dB Hz Vrms
PT2256V V1.2
-9-
August, 2006
Tel:886-2-66296288 Fax:886-2-29174598 URL:http://www.princeton.com.tw
Electronic Volume Controller IC
PT2256V
APPLICATION CIRCUIT
SINGLE POWER SUPPLY (NO LOUDNESS AND NO BACKUP CIRCUIT)
VDD (4.5 to 11V)
0.1F
L-Ch Output L-Ch Input
10F 10F
+ +
3.9K
UP Key Down Key Rx
+
Cx
VDD VSS OUT1 OUT2 IN1 IN2 LT1 LT3 AGND AGND /UP DCO /INH /DN /RST OSC
+ +
3.9K
10F 10F
R-Ch Output R-Ch Input
10K 100K
PT2256V
0.1F 10K
+
100F
Notes: 1. Modifying the values of Rx and Cx affects the Oscillator Frequency of the IC. If the Fosc value is big, then the volume control change is fast. Likewise, if the Fosc value is small, the volume control change is slow. It is suggested that Rx= 33K, Cx=2.2F. 2. The table for the Rx, Cx and Fosc values are given below: Rx 33K 33K 33K Cx 1.0F 2.2F 10F Fosc 34.1Hz 17.8Hz 3.4Hz Rx 33K 51K 100K Cx 1.0F 1.0F 1.0F Fosc 34.1Hz 22.7Hz 11.8Hz
PT2256V V1.2
- 10 -
August, 2006
Tel:886-2-66296288 Fax:886-2-29174598 URL:http://www.princeton.com.tw
Electronic Volume Controller IC
PT2256V
INCLUDING LOUDNESS BUT NO BACKUP CIRCUIT
VDD (4.5 to 11V)
0.1F
L-Ch Output L-Ch Input
10F 10F
+ +
820 8.2nF 0.1F 820 UP Key Down Key Rx
+
Cx
VDD VSS OUT1 OUT2 IN1 IN2 LT1 LT3 AGND AGND /UP DCO /INH /DN /RST OSC
+ +
820 8.2nF 0.1F 820
10F 10F
R-Ch Output R-Ch Input
10K 100K
PT2256V
0.1F 10K
+
100F
Notes: 1. Modifying the values of Rx and Cx affects the Oscillator Frequency of the IC. If the Fosc value is big, then the volume control change is fast. Likewise, if the Fosc value is small, the volume control change is slow. It is suggested that Rx= 33K, Cx=2.2F. 2. The table for the Rx, Cx and Fosc values are given below. Rx 33K 33K 33K Cx 1.0F 2.2F 10F Fosc 34.1Hz 17.8Hz 3.4Hz Rx 33K 51K 100K Cx 1.0F 1.0F 1.0F Fosc 34.1Hz 22.7Hz 11.8Hz
PT2256V V1.2
- 11 -
August, 2006
Tel:886-2-66296288 Fax:886-2-29174598 URL:http://www.princeton.com.tw
Electronic Volume Controller IC
PT2256V
ORDER INFORMATION
Part Number PT2256V PT2256V-S PT2256V-SN PT2256V (L) PT2256V-S (L) PT2256V-SN (L) Package 16 Pins, DIP, 300mil 16 Pins, SOP, 300mil 16 Pins, SOP, 150mil 16 Pins, DIP, 300mil 16 Pins, SOP, 300mil 16 Pins, SOP, 150mil Top Code PT2256V PT2256V-S PT2256V-SN PT2256V PT2256V-S PT2256V-SN
Notes: 1. (L), (C) or (S) = Lead Free 2. The Lead Free mark is put in front of the date code.
PT2256V V1.2
- 12 -
August, 2006
Tel:886-2-66296288 Fax:886-2-29174598 URL:http://www.princeton.com.tw
Electronic Volume Controller IC
PT2256V
PACKAGE INFORMATION
16PINS, DIP, 300MIL
PT2256V V1.2
- 13 -
August, 2006
Tel:886-2-66296288 Fax:886-2-29174598 URL:http://www.princeton.com.tw
Electronic Volume Controller IC
Symbol A A1 A2 b b1 b2 b3 c c1 D D1 E E1 e eA eB eC L Min. 0.015 0.115 0.014 0.014 0.045 0.030 0.008 0.008 0.780 0.005 0.300 0.240 0.000 0.115 Nom. 0.130 0.018 0.018 0.060 0.039 0.010 0.010 0.790 0.310 0.250 0.100 bsc 0.300 bsc 0.130 Max. 0.210 0.195 0.022 0.020 0.070 0.045 0.014 0.011 0.800 0.325 0.280 0.430 0.060 0.150
PT2256V
Notes: 1. All dimensions are in INCHES. 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimensions "A", "A1" and "L" are measured with the package seated in JEDEC Seating Plane Gauge GS-3. 4. "D", "D1" and "E1" dimensions do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.010 inch. 5. "E" and "eA" measured with the leads constrained to be perpendicular to datum -c-. "eB" and "eC" are measured at the lead tips with the loads unconstrained. 6. "N" is the number of terminal positions. (N=16) 7. Pointed or rounded lead tips are preferred to ease insertion. 8. "b2" and "b3" maximum dimensions are not include dambar protrusions. Dambar protrusions shall not exceed 0.010 inch (0.25 mm). 9. Distance between leads including Dambar protrusions to be 0.005 inch minimum. 10. Datum plane -H- coincident with the bottom of lead, where lead exits body. 11. Refer to JEDEC MS-001 Variation AB. JEDEC is the trademark of JEDEC SOLID STATE TECHNOLOGY ASSOCIATION.
PT2256V V1.2
- 14 -
August, 2006
Tel:886-2-66296288 Fax:886-2-29174598 URL:http://www.princeton.com.tw
Electronic Volume Controller IC
PT2256V
16PINS, SOP, 300MIL
N
INDEX AREA
H E -B-
.25 (.010) M B M
1
2
3 L
-A-
D
SEATING PLANE A -C A1 B .10 (.004)
h X 45
-e-
C
.25 (.010) M C A M B S
Symbol A A1 B C D E e H h L
Min. Max 2.35 2.65 0.10 0.30 0.33 0.51 0.23 0.32 10.10 10.50 7.40 7.60 1.27 BSC 10.00 10.65 0.25 0.75 0.40 1.27 o 0 8o
PT2256V V1.2
- 15 -
August, 2006
Tel:886-2-66296288 Fax:886-2-29174598 URL:http://www.princeton.com.tw
Electronic Volume Controller IC
PT2256V
Notes: 1. Dimensioning and tolerancing per ANSI Y14.5M-1982. 2. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold Flash, protrusion or gate burrs shall not exceed 0.15 mm (0.006 in) per side. 3. Dimension "E" does not include interlead flash or protrusions. Interlead flash or protrusions shall not exceed 0.25 mm (0.010 in) per side. 4. The chamfer on the body is optional. It is not present, a visual index feature must be located within the crosshatched area. 5. "L" is the length of the terminal for soldering to a substrate. 6. N is the number of the terminal positions (N=16) 7. The lead width "B" as measured 0.36 mm (0.014 in) or greater above the seating plane, shall not exceed a maximum value of 0.61 mm (0.24 in). 8. Controlling dimension : MILLIMETER. 9. Refer to JEDEC MS-013, Variation AA. JEDEC is the trademark of JEDEC SOLID STATE TECHNOLOGY ASSOCIATION.
PT2256V V1.2
- 16 -
August, 2006
Tel:886-2-66296288 Fax:886-2-29174598 URL:http://www.princeton.com.tw
Electronic Volume Controller IC
PT2256V
16 PINS, SOP, 150MIL
PT2256V V1.2
- 17 -
August, 2006
Tel:886-2-66296288 Fax:886-2-29174598 URL:http://www.princeton.com.tw
Electronic Volume Controller IC
PT2256V
PT2256V V1.2
- 18 -
August, 2006
Tel:886-2-66296288 Fax:886-2-29174598 URL:http://www.princeton.com.tw
Electronic Volume Controller IC
Symbol A A1 A2 b b1 c c1 D E E1 e L L1 L2 R R1 h 1 2 Min. 1.35 0.10 1.25 0.31 0.28 0.17 0.17 Typ. 9.90 BSC. 6.00 BSC. 3.90 BSC. 1.27 BSC. 1.04 REF. 0.25 BSC. Max. 1.75 0.25 1.65 0.51 0.48 0.25 0.23
PT2256V
0.40 0.07 0.07 0.25 0 5 0
1.27 0.50 8 15 -
Note: 1. Dimensioning and tolerancing per ANSI Y 14.5M-1994 2. Controlling Dimension: MILLIMETERS. 3. Dimension D does not include mold flash protrusions or gate burrs. Mold flash, protrusions or gate burrs shall not exceed 0.15 mm (0.006 in) per end. Dimension E1 does not include interlead flash or protrusion. Interlead flash or protrusion shall not exceed 0.25mm per side. D and E1 dimensions are determined at datum H. 4. The package top may be smaller than the package bottom. Dimensions D and E1 are determined at the outermost extremes of the plastic body exclusive of mold flash, tie bar burrs, gate burrs and interlead flash, but including any mismatch between the top and bottom of the plastic body. 5. Datums A & B to be determined at datum H. 6. N is the number of terminal positions. (N=16) 7. The dimensions apply to the flat section of the lead between 0.10 to 0.25mm from the lead tip. 8. Dimension "b" does not include dambar protrusion. Allowable dambar protrusion shall be 0.10mm total in excess of the "b" dimension at maximum material condition. The dambar cannot be located on the lower radius of the foot. 9. This chamfer feature is optional. If it is not present, then a pin 1 identifier must be located within the index area indicated. 10. Refer to JEDEC MS-012, Variation AC. JEDEC is the registered trademark of JEDEC SOLID STATE TECHNOLOGY ASSOCIATION.
PT2256V V1.2 - 19 August, 2006

▲Up To Search▲

Price & Availability of PT2256V

	To Download PT2256V Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .